3/5/7 ply Automatic Corrugated Cardboard Production Line For Corrugated Carton Box Making
Main technical parameters and requirements in production line
1.The maximum production width of the corrugated cardboard:1600mm
2.Design speed:100m/min
3.Economic speed:60-80m/min note:Production line speed test paper should meet the following requirements:(the surface temperature of the equipment is not less than 172ºC)Paper rating of not less than B grade
Paper moisture content of about:11%±2%
top paper:100-250g/m2
core paper:100--250g/m2
corrugated paper:100-200g/m2
4.Flute-type combination:A ,C, B, E(as customers' requirement)
5.Steam the necessary requirements:
amount of steam 2500-3000Kg/Hr the highest pressure:1.2MPa
common pressure:0.8-1.1MPa
6,power supply:380V 50Hz Three-phase four-wire system
ZJ-F shaftless mill roll stand
Structural features:
★Symmetrical structure can also install two bundles of paper at the same time,Paper can be used for non-stop for a job;Adopts mechanical drive to complete the paper clamping, lifting, loosen, move on, around translational motion, etc.
★each shaftless mill roll stand is equipped with two pieces of paper guide, two set of paper car;paper guide the use of channel 14 and the guide post weld,paper car adopt 10mmwelded stell,
RG-1-600 top(core)paper preheater
Structural features:
★In accordance with national standard category pressure vessel,and with the pressure vessel certificate.
★The roll surface after precision grinding, fine grinding and hard chromium plating processing,surface friction,durable.
★electric adjustable angle, angle can rotate in the range of 360°,and adjust the paper preheat area.
technical parameters:
1,diameter of the preheat roller:¢600mm
Diameter of the angle:¢85mm×2
2,work power:380V 50Hz
3,motor power:250W short(S2)work system
SF-280S fingerless type single facer
Structural features:
★Adopt vacuum suction structure, with high pressure strong blower.Suction with silencer.Gas supply and electrical control cabinet to focus on the same operation cabinet,not less than 1.5 meters away from the host,Fully enclosed full operation side.
★base and wallboard cast iron wall,Wallboard thickness130mm.universal Joints.
★corrugated roller material adopt 48CrMoalloy steel,quenched,Laser hardening,Surface finish,main roll of corrugated diameter¢ 280mm,surface hardnessHRC60degree above.The key parts of the tile and pressure roller bearings Wafangdian produce high temperature bearings.
★pressure roller ¢ 284mm,surface grinding and chrome-plated;cylinder control and remove up and down, 45 carbon steel materials, quenching (with cushioning devices).
★pneumatic control glue to glue back, glue roller diameter ¢215mm,Engraved polished surface after a 36-line pit style textured machined chrome plated,after scraping the roller surface polished hard chrome plated.
Regular technical parameters:
1,effective width:1600mm
2,operation direction:left or right(determined in accordance with customer plant)
3,design speed:100m/min
4,temperature range:200-260ºC
5,corrugated flute:(UV type or UVV type)
RG-2-600 triple preheater
Structural features:
★preheat roller accord with the national standard of the pressure vessal,and enclosed the pressure container certificate and inspection certificate.
★Each roller surface after grinding precision grinding and dealing with hard chrome plating, Surface friction is small, durable.
★electric adjustable angle, it can rotated adjust the paper preheat area in the range of 360°.
GM-12 double glue machine
Structural features:
★After the glue roller surface after quenching inner hole machining, grinding and dynamic balancing surface engraved with pit style textured, coating evenly, less consumption of plastic.
★doctor roller surface by grinding and hard chromium plating.
★other guide rollers with hard chrome plated.
★Pressure roller with pneumatic lift, easy operation.
★ manually adjust scraping gap.
★glue roller ¢ 215mm,Doctor roll¢ 122mm,press paper roller¢ 122mm,preheat roller 270mm.
★Electrical design, construction production process, follow the national standards, low failure rate, easy maintenance.
regular technical parameters:
1,MAX.working width:1600mm 2,operation direction:left or right(Determined in accordance with the customer's facility)
3,design speed:100m/min 4,Gas supply system:0.4-0.6Mpa
5,Preheat cylinder temperature range:150-200ºC Steam pressure:0.8-1.2Mpa
SM-10 type double facer
Structural features:
★Heating plate surface by grinding treatment, hot plate width 600mm, a total of 12 heating plate and cooling 4 m.
Heating plate with a container board production, in line with national standards for a class pressure vessel, with pressure vessel certificate and inspection certificate.
★Hot plate with intensive gravitational roll structure. Roll adopt pneumatic lifting.
★Heating plate heat transfer pipe temperature control sub-four-segment, with a temperature display.
★on cotton use two-cylinder S type cotton belt with the tensioning device.
Mainly purchased parts, raw materials and origin:
| Name of main parts |
Brands or place of origin |
Material and type |
| Main skeleton |
Tiangang or laigang |
NO36Channel steel |
| preheater |
Dezhou luxing chemical factory |
Q235BContainer board production |
| Main drive motor |
Hebei hengshui |
frequency motor |
| Cotton belt |
Shenyang |
|
| traps |
Beijing |
Inverted bucket |
| contacts |
France |
|
| button |
Chint NP2 series |
|
Air switchs
Air switch |
France |
|
| Frequency machine |
Taiwan delta |
|
| bearing |
HRB,ZWZ,LYC |
|
| Drive wallboard |
Production by own |
|
| Pneumatic elements |
Japan SMC or AirTAC |
|
ZQS thin knife slitting
structural feature:
★Overcome the conventional type of pole, cutting pressure lines appear when collapsed cardboard cut phenomenon, cutting board smooth, quality has improved significantly.
★the whole machine can remove left and right,cycloid reducer to adjust.
★Cutter and easy to adjust the pressure line, the error ± 0.5mm, automatic sharpening device, you can achieve timing Brothers, with intermittent Brothers and other features.
★the machine adopt five knives eight lines,the blade is made of tungsten alloy steel, the using life is not less than 3 million running meters.
NC-120 NC cutter helical knives
structural feature:
★it can store 200 units orders,replace the cutter specifications quickly and accurately,changing orders without stop,And enables networked computers to facilitate production management.
★Knife shaft drive gears are precision forged steel induction hardening, backlash-free transmission, advanced keyless connection, high transmission accuracy.
★Cutting machine adopts inlaid front steel blade knife spiral structure, serrated knife. scissors, shears, shear force, long blade life.
★around feed rollers are used the sun gear platen way, smooth delivery, pressure evenly, easy to crush plate board or cause blockage.
★Exact and adjustable no gap gear to ensure precise blade engagement, running balance.
technical parameters:
1.Horizontal body glue mixer: one
2,Carrier glue mixer:one
3,Storage glue mixer: one
4,Plastic buckets on double coater: one
5,Two coating machine back plastic buckets :one
6,Plastic buckets on single machine :two
7,Single machine back plastic buckets: two
8,Lose glue dispensing pumps: four
glue barrel diameter parameters:
1,Horizontal body glue mixer:1250mm×1000mm×900mm
2,Carrier glue mixer diameter: ¢800mm×900mm
3,Diameter plastic bucket on Double Glue:¢800mm×1000mm Plastic buckets on single machine:¢800mm×1000mm
4,Storage tank diameter: ¢1200mm×1200mm
Power motors and electrical parameters:
1,Horizontal body glue mixer: 3Kw 380V 50Hz
2,Carrier glue mixer: 2.2Kw(Ordinary three-phase) 380V 50Hz
3,output plastic pump motor : 2.2Kw(Ordinary three-phase) 380V 50Hz
4,Storage Tank Motor 1.5Kw(Ordinary three-phase) 380V 50Hz
More details pls call us WA
FAQ
1. who are we?
CHINA YIKE GROUP, Which based in Hebei, China, start from 2002,sell to Mid East(24.00%),South America(21.00%),Eastern
Europe(15.00%),Africa(10.00%),Southeast Asia(10.00%),North America(5.00%),Western Europe(2.00%),Southern Europe(2.00%),Eastern
Asia(10.00%). There are total about 5-10 people in our office.
2. how can we guarantee quality?
Firstly pre-production sample before mass production;
Secondly Inspection before shipment;
3.what can you buy from us?
Corrugated Cardboard Production Line,Carton Box Making machine, Box Printing Forming Machine, Auto folder gluer, sitching machine, die cutting machine, bundling machine..
4. why buy from us not from other suppliers?
Factory related carton machinery import & export company, based on more than 30 years experience in providing complete and carton machinery solutions according to different customer situations and requriements. reliable quality and good service on site.
5. what services can we provide?
Accepted Delivery Terms: FOB,CFR,CIF,EXW,FAS,CIP,DDP,DDU,Express Delivery,DAF,DES;
Accepted Payment Currency:USD,EUR,JPY,CAD,CNY;
Accepted Payment Type: T/T,L/C,D/P D/A,MoneyGram,Credit Card,PayPal,Western Union,Cash;
Language Spoken:English,Chinese,Spanish,Portuguese,Arabic,French,Russian,Italian
Audited Supplier 
){kind=link}